The Nanometer Precision Race: Multilayer Piezoelectric Ceramics and the Future of Camera Stabilization and Focus
Introduction: A New Battle Inside Every Flagship Camera
Smartphones have replaced handheld cameras for most people. Now it's the phone that goes to a wedding or to the hiking trails or brings to a concert. Due to the change, two of the most significant features that distinguish a flagship phone from average are now the image stabilization and auto-focusing.
The competition has moved past megapixel counts. Camera engineers now compete on how precisely a lens module can hold still and how fast it can lock focus. This race has pushed telephoto lenses, macro lenses, smart wearables, and action cameras toward a level of positioning accuracy that traditional actuator technology struggles to reach.
At the center of this shift sits a component that rarely gets public attention: the multilayer piezoelectric ceramic. This material is used in optical image stabilizing (OIS) or autofocusing (AF) systems operating as the working heart of an electronic motor of the rollers.
Bestarsensor has spent years building deep technical experience in multilayer piezoelectric ceramics, from material formulation to co firing process control. This article looks at why this material matters so much for optical modules today, and what stands behind Bestarsensor's engineering capability in this field.
Why Multilayer Piezoelectric Motors Are Becoming Hard to Replace in Optics
Nanometer Positioning for Sharper Focus
Telephoto and macro lenses ask for very fine, very repeatable movement. Traditional electromagnetic motors use mechanical gears and springs and these have small amounts of play or backlash. The backlash isn't an issue with a wide angle lens. When it has to focus a few microns or correct hand shake when shooting a tele photo module from a distance it becomes a real problem.
The multi-layer piezoelectric motors react in a few micro seconds of time and can move with nanometer precision. This makes a module slide easily through a zoom without gap. This enables a macro camera to fix speedily on the fine detail that a slower system would miss.
No Magnetic Interference
Wearable devices and action cameras pack a lot of sensors into a small space. Many of these devices carry an electronic compass or a magnetometer close to the camera module. A traditional voice coil motor works by generating a magnetic field, and that field can disturb nearby magnetic sensors.
Piezoelectric motors work through mechanical deformation of a ceramic material, not through a magnetic field. This gives them a natural advantage: the stabilization system can run at full speed without throwing off the compass reading or the motion sensor next to it. For any device that depends on accurate direction or orientation data while filming, this property is not a minor detail. It is often a design requirement.
Low Voltage Drive in a Thin Package
The multilayer piezoelectric actuator consists of a number of alternating thin ceramic layers between which are the internal electrodes, and these layers, along with the electrodes, are co-fired to form a single block. In this construction the layers collaborate in the place of a single thick ceramic actuator that would have to operate on a much larger voltage.
This matters directly for smartphone design. Internal space inside a flagship phone is extremely tight, and every millimeter around the camera stack is fought over by the battery, the antenna, and the thermal system. A thin, low voltage multilayer stack
This is not only a design idea on paper for Bestarsensor. The same thin, low voltage multilayer ceramic structure already drives ultra thin piezoelectric components running inside real consumer products on the market today, not just early stage samples. That working history gives engineering teams a practical reference point when they judge whether a design can move from prototype to volume production.
The Structural Advantages Behind the Motor
Three structural properties explain why multilayer piezoelectric ceramics keep winning design slots in optical modules.
High energy density and strong output force. A multilayer stack converts electrical energy into mechanical force very efficiently for its size. A small ceramic block can produce enough thrust to move a lens group, without needing a large actuator body.
Fast response with almost no mechanical lag. The ceramic material itself moves when voltage is applied. There is no gear train and no spring tension to overcome first. This gives a start stop response measured in milliseconds, well ahead of what a geared electromagnetic motor can deliver.
Long service life with low power draw. Because there is no mechanical gear meshing and no sliding metal contact under load, wear is much lower. A phone camera module goes through an enormous number of small stabilization corrections every time a video is recorded. A piezoelectric actuator handles that repeated, high frequency movement with far less material fatigue than a geared mechanism, and it draws less standby power in the process.

Bestarsensor's Multi Year Technical Foundation in Multilayer Piezoelectric Ceramics
Camera actuator performance ultimately comes down to how consistent the ceramic material and the co firing process are, batch after batch. This is where Bestarsensor's long term investment in multilayer piezoelectric ceramics becomes relevant to any engineering team evaluating a supplier.
Bestarsensor's technical foundation in this material is not built on a single product line or a single internal research team. Over the years, the company has kept an ongoing connection with universities, research institutes, and wider industrial technical resources. Its public academic network reaches institutions such as Tianjin University, Sichuan University, Nanjing University of Aeronautics and Astronautics, and the Shanghai Institute of Ceramics under the Chinese Academy of Sciences, among other partners. Through this continued collaboration between in house engineering capability and outside academic research, Bestarsensor has gradually built an R&D base that covers ceramic materials, multilayer structural design, and precision manufacturing process control. This base gives new microdevices a real path from early technical exploration to engineering application, rather than leaving them as lab concepts.
Precision manufacturing sits at the center of that path. Bestarsensor maintains process controls for high accuracy multilayer co firing and micron level electrode processing, which is what keeps physical and electrical performance consistent across a full production batch, and this matters greatly to a camera module manufacturer that needs every actuator on the line to behave the same way.
Bestarsensor also applies this multilayer piezoelectric ceramic expertise beyond smart terminal optics, extending into medical devices, microfluidics, and industrial high precision positioning, giving partners a single technical team that can support several application areas at once.
Conclusion: A Materials Race Underneath the Camera Race
The race to build sharper, steadier phone cameras is really a race between underlying drive materials. Traditional electromagnetic motors are reaching the limits of what mechanical gears and magnetic coils can deliver inside a space this small. Multilayer piezoelectric ceramics answer that limit directly, with nanometer level precision, no magnetic interference, and a thin, low voltage structure that fits modern device design.
Bestarsensor brings a multi year technical foundation to this shift, built on ongoing academic cooperation and a proven path from ceramic material to mass production.
Engineering teams working on high precision optical modules, miniature actuators, or high precision positioning systems are welcome to contact the Bestarsensor technical team for consultation and evaluation support on multilayer piezoelectric ceramic solutions.


Nov,06 2026